1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

848 Quickshifter Wire Loom Question

Discussion in '848 / 1098 / 1198' started by Chris2511, Feb 24, 2017.

  1. Hi all

    Currently fitting my HM Plus SS quickshifter to my 848 as I type[​IMG][​IMG]

    And plugged in the new loom tired to start it up just to check it's correct and it won't fire up

    Plugged the OEM loom back in and fires up

    1 question I have is what is this extra lead I have at one end??? Does it matter if this is on the rear cylinder or front ? Can't see where else it plugs into

    Cheers for a quick response


    Sent from my iPhone using Tapatalk
     
  2. It matters front and/or back.
    Is it gounded?
     
    • Like Like x 1
  3. Not grounded yet no

    I haven't put on the strain gauge etc

    Literally just plugged into the coil plugs to test it was ok before fitting the rest


    Sent from my iPhone using Tapatalk
     
  4. Ground it, they will come...
     
    • Like Like x 1

  5. Ok cheers


    Sent from my iPhone using Tapatalk
     
  6. Yeah... Everything needs to be connected.... And yes, get a good ground!

    Sent from my SM-P900 using Tapatalk
     
    • Like Like x 1

  7. Ok cheers guys appreciate the help as always


    Sent from my iPhone using Tapatalk
     
  8. That 'spare' connector look like it was the one the shifter goes in.
     
  9. Yeah I realised not long after posting ....'bangs head off the wall'


    Sent from my iPhone using Tapatalk
     
    • Like Like x 1
  10. Ok got it all plugged in the LCD control only shows part of the countdown then stops for the set up mode

    5.4..... then nothing

    I have earthed it to the negative on my battery ?

    Any ideas ?


    Sent from my iPhone using Tapatalk
     
  11. Is it the hm plus? (the one with the little red box)?

    Sent from my SM-G935F using Tapatalk
     
  12. It's the Plus SS with a black box mate ?

    It should count down from 5.4.3.2.1 then go into set up mode

    But it's getting to 4 then just going to blank screen again

    Something is telling me the earth isn't good


    Sent from my iPhone using Tapatalk
     
  13. Sounds like it works the same as mine... Give me a min I'll just pop in the garage and check.... Try taking a cable from your earth point straight to the battery... While in checking...

    Sent from my SM-P900 using Tapatalk
     
    • Like Like x 1
  14. I have a very vague memory that mines does the same run down, I checked with HM and it's a peculiarity of the way Ducati's power up. IIRC
    Put the bike on a paddock stand and try putting it through the gears without the clutch.
     
    • Like Like x 1
  15. Mine only counts down when I hold my finger down on the button and switch the ignition on... But it is on a z1ooo....

    Sent from my SM-G935F using Tapatalk
     
    • Like Like x 1
  16. That's the configuration button on the back of the box...

    Sent from my SM-G935F using Tapatalk
     

  17. Will give this a whirl tomorrow


    Sent from my iPhone using Tapatalk
     
  18. The spark plugs are only live for few seconds when turn ignition on.
    You need to keep little button pressed on unit and start bike. Plugs are live again and will count down to 0 and let go to enter set up mode
     
    • Like Like x 1
    • Useful Useful x 1

  19. Cheers Jase will give it a try tonight

    Thanks for your help will post how I get on


    Sent from my iPhone using Tapatalk
     
    • Like Like x 1
  20. I personally wouldn't worry about set-up right now. It should be plug and play.
     
Do Not Sell My Personal Information